viagra news today tomar viagra com antibiotico faz mal o viagra faz mal ao coracao levitra bula para que serve levitra preco infarmed what is levitra

Sonic Dissonance - Daily Health and Life Improvement PracticesOur Blog

4 Easy DIY’s To Get Rid of Hard Water Scale Buildup

Are you dealing with hard water scaling issues? No need to buy expensive cleaners anymore as we have some handy DIYs for you.

You can call it hard water stains, limescale, mineral deposits or mineral build up, etc; all is one and the same thing. It is a crusty white film that or say it JUNK that builds around faucets, sink, shower heads, bathtubs, and toilet. This forms when hard water evaporates leaving behind minerals mainly calcium and magnesium that solidify forming a whitish cast that is hard to remove.

There are many cleaners available in the market but they are filled with harsh chemicals. Hence should be used in minimal amount but what about a daily nuisance? Well, you can easily get rid of them. We bring you DIY’s that are pocket-friendly as well as safe for your appliances.

Do you wish to eradicate hard water problems completely? Then go for water softeners that are a one-time investment and cost-effective. Once installed you are free from all hard water problems and free minded. Before you buy check top 10 salt free water softeners so that you pick the right system as per water conditions of your area.

Now, as we have discussed above that water softeners are the best resolution till then you can implement these DIYs for limescale issues.

  1. Faucets: Soap a paper towel in vinegar and wrap it on the faucet. Let it sit for 30 minutes. You can fill it in the spray bottle also. Later wipe it with a clean cloth.
  2. Coffee Maker: Add a cup of white vinegar and a cup of water (fill it to the top-increase quantity as required). Run coffee maker and rinse with warm water. Again fill with water and boil, rinse.
  3. Tea Kettle: Add two denture tablets and water in the tea kettle or antacid tablets. Let them dissolve and boil water. Later boil water and rinse the kettle.
  4. Bathtub Taps: Squeeze lemon juice and fill in a spray bottle. Directly spray it on the faucets or taps. Let it sit for 30 minutes, scrub a little and wash with hot water.
  5. Showerhead: Either affixes a carbon filter or takes out the shower head and dip in the vinegar solution for 20 to 30 minutes. Later rinse it with water and put it back.

You can use vinegar on the toilet seat, tiles, faucets, taps, bathtubs, sink, electric kettle and coffee maker to remove stains and crusty residue formed due to water hardness. This is the best solution. If you run out of vinegar substitute it with lemon or coke. Both work well for limescale problems.

We all know that limescale causes stains and looks ugly as mentioned vinegar is anti-scaling (white vinegar). You can take a clean cloth and dip in vinegar wrap it around faucets. Later clean with a clean cloth. This works wonder too and creates no mess. The choice is yours whether you use it in a spray bottle or in dipped towel results will stun you.


No kidding! All the methods listed above are tested. Once I did these tests and used water tap next thought was again I need to clean it up. But NO, there was no need to repeat the process. Just one treatment and limescale was gone.

I am thankful for this method. Now no hard water worries. Super Happy! Do try and tell us how you felt.

How To Get Rid Of Weeds Around Shrubs

Weeds growing around shrubs can be annoying and stressful to get rid of. As you fertilize and take care of shrubs, some strains of weed have a penchant for thriving off the fertile soil around the shrubs. There are quite a few ways for removing and preventing weeds from growing around shrubs. Weeds can be pulled out manually or killed using herbicides. If done without care, weeding using herbicides can affect the shrubs or even kill them.

1. Targeting weeds using a cardboard or plastic cover

Herbicides can be used to kill grown weeds and create non-conducive soil from which weeds cannot survive. Liquid herbicides can be sprayed directly on top of weeds that are intertwined or mixed with the shrubs. An easy way to target weeds that are mixed with shrubs is by placing a cardboard or plastic cover over the shrubs and pull the weed through a hole on the cover. Spray the weed with the herbicide then remove the cover after the herbicide has dried. Large weed patches can be targeted using a large cardboard or plastic cover with a sizable hole. Place the cover over the shrubs with the hole over the weed patch then spray over the weeds with the herbicide. It is essential to remove the cover after the herbicide has dried to prevent the shrubs from contacting the herbicide.

2. Targeting weeds using u-shaped anchor pins

Weeds growing at the edges of a shrub plantation can be targeted using a u-shaped anchor pin to isolate them from nearby shrubs. It is important to ensure the pin is in a stable setting to avoid destabilizing by strong weed stems. The pin anchors the weed as the herbicide is applied to them. Herbicide can also be applied directly onto weeds’ leaves using sponge applicator brushes or bristle brushes. Care should be taken when using bristle brushes to avoid flicking the herbicide onto the shrubs.

Putting a cover around the shrubs Another way to control weed presence is to place a plastic sheet over the soil around the shrubs to prevent weed seeds from germinating. A dense sheet of mulch can also be applied in place of the plastic. Polyester landscape cloth can also do the job well

3. Hand-pulling isolated weeds

Hand-pulling is the best and environment-friendly method to eliminate weeds around shrubs. Be sure to wear gardening gloves to protect your hands. The roots and lower stems should also be pulled when ridding the shrub plantation of weeds or else they will grow back. The soil around the roots may be dug out to reduce the chance for the weeds grows back. The tool used to dig out the soil must be cleaned before using it on another section of the plantation to avoid spreading the weeds.

4. Installing headers around the shrubs

Headers act as walls around the shrubs. They help to minimize the chance for weed seeds being dispersed into the shrub plantation. Headers should be buried at least 10 inches below the soil line and stick a few inches above the soil line for maximum effectiveness.

A bonus tip is to use fertilizer sparingly. Only use fertilizer when the soil is poor, or the shrubs look unhealthy. Weed elimination can be expensive and burdensome; hence it is wise to abide by Ben Franklin’s words, An ounce of prevention is worth a pound of cure”.